Shiplap gives you the casual, farmhouse feel that so many of us are after. It can be done relatively easily and for very little money. Although there may be hundreds, if not thousands, of posts on how to faux shiplap walls, each one gives some insight and tips on how to do it a little differently and maybe a little easier than others. I hope in this post, I’m able to do just that! And if you ever wondered if you can use plywood to shiplap walls in the bathroom, the answer is absolutely! Keep reading and I’ll share some tips what to buy and how to get the best results.
We used 3/8″ exterior-grade plywood, also know as CDX plywood, for our master bathroom walls. I explain why we chose that type of plywood in this post. For future projects, we’ll be using CDX plywood anytime we plan to plank our walls again.
Putting ship lap on the walls may seem intimidating at first, but really it’s just a matter of getting the boards cut, nailing them onto the walls, sanding, and then painting.
*affiliate links are included*
These are the steps we took to get the shiplap-look for less:
Step 1: Figure out how many sheets of plywood you need and add 15% for waste. Rip your plywood sheets into anywhere between 6″ to 8″ strips with a circular saw or table saw. We chose to cut ours 6″ wide. In order to have the least amount of waste, we cut our strips 5-13/16″ wide. This takes into consideration the kerf (or width) of the saw blade which is approximately 3/16″. You can also have the guys at the home improvement store cut the plywood for you for about $0.25 per cut. Their blade’s kerf may be wider.
Tip: From experience when I did my board and batten hallway project, if you send the wife to get the boards cut instead of the husband and go when it’s not as busy, you might just get the cuts done for free. Also, it helps to tell them you’re not in a rush and you’re willing to come back in a couple hours. And smile…and say please. 😉
Step 2: Remove the baseboards.
Step 3: Mark your studs. By the way, I found my favorite stud finder ever! It never needs batteries and it sticks to the wall once you find your stud.
Step 4: Start from the ceiling since it’s more visible than the bottom of the wall. Since we’ll be adding crown molding, we started our first run of boards 1-1/2″ down from the ceiling so we’d be covering up the least amount of board. Make sure the first run of boards is perfectly level and nail the boards into the studs. We chose to not use construction adhesive.
Step 5: Use a nickel as a spacer between the row of boards. Recheck that the rows are level about every other row.
Tip: Removing the trim below the window will save you time and aggravation since you won’t have as many cuts around the trim. We removed our lower window trim because the depth of the planks would’ve hidden the profile of the trim.
Step 7: For walls wider than 8 feet, you’ll need to stagger the boards. If possible, cut your boards so they end at a stud. Keep in mind that studs are an inch and half wide. The end joint on the shiplap pieces need to meet on a stud halfway.
Step 8: Fill the corners of the walls and around windows and doors with caulk. Fill your nail holes and any wood knots with wood filler. Some folks choose to not fill the nail holes. Really, it’s just a personal choice. If you notice in this picture of Chip and Joanna’s kitchen, the nail holes aren’t filled in their authentic shiplap.
Step 9: Lightly sand the walls and where you filled the nail holes and knots.
Step 10: Spot prime over the knots with B-I-N Zinsser shellac primer to seal the knots and prevent the from sap bleeding through the paint. Then, use an all-purpose interior/exterior primer for the rest of the walls. Roll the primer on and use a brush to get between the cracks. A paint sprayer really helps to speed up the process…trust me. I switched to spraying after the first day of painting.
Step 11: Now you’re ready for the part that transforms it all…the final coats of paint! We went with Sherwin Williams Natural Choice SW 7011 in Satin. It’s on the same color strip as Alabaster but it’s creamier and not as bright white. I’ve recently switched to their Harmony Low VOC line and I’m very happy with the coverage.
And, oh yeah…lighting does an amazing job transforming a space too!
Jason’s building the double vanity and chandelier. My parents are coming into town to bring the shower enclosure and help us install it. It’s a wedding gift/ birthday gift and I’ll be forever grateful! Then, we’ll be working on the concrete countertops. They’re gonna be gorgeous, folks!!
Have you put shiplap up before? If you guys have any tips and tricks, I’d love to hear them!
Catch up on all the posts and projects that went into our master bathroom remodel here:
Sharing with some of my favorite blogs such as: